you can play games with LAN and WLAN. This tutorial will Guide you How to play using LAN/WAN and if you do not have any knowledge about connections refer these two tutorials.
* Build your own network via Wireless LAN
* Build your own network at home
Build your own network via Wireless LAN
WLAN technology
WLAN technology
wireless Local area network.
The complete networking here is done with no wires involved. These are basically computers which covers a wider or a broader area. It is helpline where people or users from one organization want to access the computers of other organization. These are few steps by which you will learn to network via WAN.
1. If you have a laptop then no problem as in desktops there is no Wi-Fi service.(recommended laptop)
2. Switch on the Wireless LAN of the laptops you want to connect.
3. In this you will have to create a server to which the other laptops will connect.
4. for creating a server go to control panel>Wireless Network Setup Wizard.
5. Give the desired network name and for security you can either manually assign or an automatic facility is also provided.
The complete networking here is done with no wires involved. These are basically computers which covers a wider or a broader area. It is helpline where people or users from one organization want to access the computers of other organization. These are few steps by which you will learn to network via WAN.
1. If you have a laptop then no problem as in desktops there is no Wi-Fi service.(recommended laptop)
2. Switch on the Wireless LAN of the laptops you want to connect.
3. In this you will have to create a server to which the other laptops will connect.
4. for creating a server go to control panel>Wireless Network Setup Wizard.
5. Give the desired network name and for security you can either manually assign or an automatic facility is also provided.
In case of manual assigning the key should be exactly 5 or 13 char long. Ones done with this, insert a pen drive and copy the file which you have generated through the wizard.
Your server is created.
Ip Address Assigning
1. After this process the next part is of assigning of ip addresses.
2. Go to Start>Control panel>Network Connections>right click on Wireless Area Connection>properties> (TCP/IP)>properties.
3. click on Use the following IP address: the next step is to put IP addresses.
4. Remember you have to put IP addresses ranging from 1 to 254 only.
5. For instance you can put
IP address: 192.168.1.1
subnet mask:255.255.255.0 (will appear by default)
Default gateway: put same as IP address.
(Done for the 1st pc)
Follow the same steps for the second PC but here you Just have to change the IP address, for instance you can keep it 192.168.1.2 and the other two kept same.Save the settings for both the computer. To test whether the network is working fine you can go to cmd and type in “ping ip” without quotes. If you get a reply, then your network is setup successfully.
pinging a computer
The entire game play here is done with the help of routers, switches etc
Build your own network at home
Now Tutorial on How to built a network via LAN
* LAN Cable with rj45 connectors
* Computers between the networking is to be done.
RJ45 is basically called as Register Jacket. It is a piece of plastic bound with different types of wires in a particular and sequential range for the purpose of running of different applications. This jack helps to enable you to to ping with the other node
Entire networking is based on the TCP/IP ports explained in my previous posts. Each computers should be provided with its individual IP address. IP address are basically classified in 3 types A, B, C
ranging from 1 to 255. This range is as follows.
Class A- 0 to 127
Class B- 128 to 191
Class C- 192 to 223
A local area network gives networking features to the computers in close distance with each other in an office,school, building etc.However a LAN can be connected to many LANs based on a varied distance using telephone lines, radio waves.Here are some steps which can help you to built a network at your home on your own.
* The first and the basic step before setting up a network is to check whether LAN drivers are successfully installed on both the computers.
* Then you have to insert both the connectors on the respective computers rj45 ports.
* Ones you are done with it, the next part is of assigning IP addresses.
* Go to Start>Control panel>Network Connections>right click on Local Area Connection>properties> (TCP/IP)>properties.
* click on Use the following IP address: the next step is to put IP addresses.
* Remember you have to put IP addresses ranging from 1 to 254 only.
* For instance you can put:
IP address: 192.168.1.1
subnet mask:255.255.255.0 (will appear by default)
Default gateway: put same as IP address.
* The first and the basic step before setting up a network is to check whether LAN drivers are successfully installed on both the computers.
* Then you have to insert both the connectors on the respective computers rj45 ports.
* Ones you are done with it, the next part is of assigning IP addresses.
* Go to Start>Control panel>Network Connections>right click on Local Area Connection>properties> (TCP/IP)>properties.
* click on Use the following IP address: the next step is to put IP addresses.
* Remember you have to put IP addresses ranging from 1 to 254 only.
* For instance you can put:
IP address: 192.168.1.1
subnet mask:255.255.255.0 (will appear by default)
Default gateway: put same as IP address.
(done for the 1st pc)
Follow the same steps for the second PC bt here you Just have to change the IP address, for instance you can keep it 192.168.1.2 and the other two kept same.Save the settings for both the computer. To test whether the network is working fine you can go to cmd and type in “ping ip” without quotes. If you get a reply, then your network is setup successfully.
Pinging a Computer in my network
ipconfig command is used to get your ip address and other connection details.
Sharing is very important, for a successful usage of documents between two computers. This process is very simple.
Just right click on the folder you want to share, go to sharing and security, and just allow the folder to be shared. Finish it, now you can access the folder on other computer from My Network Places else you also have a another trick to do it, as you have to go to StartMenu> Run and type there \\ip of the computer on the network you want to access. When you type this command, it will eventually show you the shared files on the network. After this process you can access all the files shared on the network just as shown in below pic.
1 comment:
Sorry for my bad english. Thank you so much for your good post. Your post helped me in my college assignment, If you can provide me more details please email me.
Post a Comment